BLINDER Upgrade Kit M47/M27 X-TREME (i pro čidla M25/45 Rev.J17)

BLINDER Upgrade Kit M47/M27 X-TREME (pro Blinder čidla M25/45 Rev.J17 a nová čidla Series7 - M27&M47)

Čidla Rev.J16 a starší nelze upgradovat !!! Rev. čidel naleznete na samolepce na zadní straně čidel...

BLINDER CPU Upgrade Kit sestává z

• nového Blinder CPU boxu (vybaveného mikropočítačem a USB portem) :
  BLINDER CPU Box for BLINDER M27 & M47 X-TREME INTERNATIONAL VERSION (lze sehnat za 135 EUR u výrobce)
  
• Dále od nás dostanete zdarma jako bonus:
• nový kabelový svazek s novým 3 polohovým přepínačem
• klasický varovací pípák s diodou
   

Montáž: jednoduše vyměníte starý Blinder Interface box a kabelový svazek za nový Blinder CPU box a nový kabelový svazek (obsahující již 3-polohový spínač) - vše (box, vypínač, dioda) má naprosto identické rozměry pro snadnou výměnu; čidla Blinder Xtreme M25/M45 Rev.J17 zůstávají nainstalována ve voze a zaktualizují se automaticky přes nový Blinder CPU Box (vybavený mikroprocesorem).

K novému CPU Boxu můžete integrovat do vozu i USB kabel, pro snadné upgrady přímo ve voze.

Po prvním zapojení a zapnutí napájení toto nevypínejte, dokud zařízení pípá, cca 1-2 minuty !!!) se Rev.J17 čidla zaktualizují z CPU boxu (tento se aktualizuje přes USB kabel), prostudujte návod pro upgrade Blinder M27-M47 upgrade kit help.pdf

Pozn: tento CPU kit
- lze použít i pro opravu/vykradení M27/47 ... pokud máte poškozený / ukradený CPU box k Vašemu M27/M47.
- je určen pro Region 1 - tedy pro Evropu včetně ČR, Maďarska (pro Maďarsko existuje odlišný SW), Kanadu apod. Není určen pro regiony 2-6 tj. pro USA, Afriku, Austrálii.

-------------------

BLINDER M27 / M47 Upgrade Kit Installation guide:

This upgrade kit will only work with Blinder M25 / M45 Systems manufactured in the period from Marts to June 2009:
Rev. J17 –Series Numbers starting
Blinder M45: SCA 45.0001 / Blinder M25: SCA 25.0001
This BLINDER M27 / M47 Upgrade Kit consists of 2 parts, the CPU box, replacing the old interface box and a new 3-position on-off switch with wires, replacing the old contacts and wires. The new CPU box is in contrast to the old interface equipped with micro processes (CPU).
Disconnect the old interface
Step 1: Turn off the switch.
Step 2: Disconnect all plugs on the existing interface.
Step 3: Disconnect the power (red) -and ground wires (black). Also the Blue (Audio mute) if connected.
1
Connect the new interface (now called the CPU)
Step 4: Connect the red, black and (blue) wires to the car’s electrical system. Ensure that the switch is in position “0” for off before connecting.
Step 5: Connect the new 3-Position switch to the jack on the new CPU.
Step 6: Connect the old speaker / LED plug to the jack on the new CPU.
Step 7: Connect all the transponders to the CPU.
System initializing and software update
Before the system works correctly, the system has to go through an initializing procedure. This procedure will start automatically first time the system is turned-on after the installation of the new CPU.
Step 8:Turn on the power (switch position I or II)
Step 9:The system will now start to update one transponder at the time during which period the system is flashing (GREEN) and beeping quickly. It takes approximately 5-10 seconds for each transponder.
2
3
Step 10:When all units have been updated you must switch the power off and on again, after which the system is fully updated and ready for use.After switching the power on again, the system will flash red and beep 1 or 2 times depending on the switch position (As in normal upstart)Next time you update the system with new software all transponders will be updated automatically.
4
Important! The power must be switched off and on again between updating each transponder!
Warning!
Never turn off the power during the initializing procedure!
If the system in any way is interrupted during the initializing procedure you may end up with a not-working system.
In this case you need to download special repair software from www.blinder.dk. Here you will also find all necessary help instructions.
Online Support
Please check for the latest new help files and additional product information on www.blinder.dk.